top of page

Electric Guitar Hum and Noise: What's Normal and What Isn't

6d
4 min read

Even a guitar in good working order can hum, especially when you play through a single-coil pickup, meaning a pickup with one coil. A few simple checks at home will help you tell expected hum apart from interference in the room or a fault in your gear.

First Checks, Without Opening the Guitar

  1. Plug the guitar straight into the amp. Use a cable you know is good, choose a clean channel with no distortion, and take the pedals out of the chain.

  2. Go through the pickup selector positions. Notice in which positions the noise gets louder and in which it gets quieter. Then turn the guitar's volume down to zero. If you still hear noise, whatever is left isn't coming from the pickups.

  3. If you can, plug in another guitar. Use the same cable and the same amp to see whether the noise shows up with it too.

  4. Check the room. Turn off or move away from screens, LED lighting, dimmers and phone chargers. Check each source separately to hear what changes.

Mains Hum in Single Coils

A single coil picks up not only the movement of the strings but also changing magnetic fields around it, for example near transformers and power supplies. This can create hum at the mains frequency and its multiples. In Israel the frequency is 50 Hz and in the US it's 60 Hz, hence the name 60-Cycle Hum.

This kind of hum from a single coil on its own isn't a fault in itself. If it changes when you turn the guitar or move away from electrical equipment, that's a clue the interference is coming from your surroundings, not proof of a specific source. Screens, lighting and dimmers can also add a sharp buzz or hiss.

Reducing Hum When Two Pickups Work Together

When two matched single coils work together, the magnetic hum usually drops considerably, while the sound of the strings remains. (In an arrangement called RWRP, the coil winding direction and the magnet polarity of one pickup are reversed relative to the pickup it's combined with.)

On a Strat with an RWRP middle pickup matched to the other two:

  • Positions 2 and 4: Bridge and middle, or middle and neck, work together and greatly reduce the hum.

  • Positions 1, 3 and 5: Only one pickup is working, so it hums like a regular single coil.

How much the hum drops depends on how well the coils are matched. A humbucker works on the same principle, but both coils sit inside one pickup.

In Vergatto single-coil and P90 sets, one pickup is always wound and polarized in reverse relative to the pickup it combines with. In Strat-style sets, that's the middle pickup. That way, the combined positions reduce hum. When you order an installation from us, you can also ask for wiring that runs two single coils together in more positions to reduce hum, at no extra charge.

What Changes When You Touch the Strings

The Buzz Gets Quieter

When the strings are connected to the guitar's ground, touching them also connects your body to that same point in the circuit. Touching them usually reduces buzz that comes from electric fields around you. Shielding can help too: line the cavity under the knobs and selector with copper foil or conductive paint, and connect the lining to ground. Shielding reduces this type of buzz, but it doesn't stop a single coil's magnetic mains hum.

The Noise Gets Louder

First try a good cable plugged straight into the amp. If the noise still gets louder when you touch the strings, have the wire that connects the bridge to ground checked. If the noise started after wiring work, the two wires on the jack the cable plugs into may have been swapped.

If you feel a tingle or an electric shock from the strings or the microphone, stop playing, turn off the equipment and unplug it from the mains. Have a technician check the amp and a licensed electrician check the wall outlet. Never remove or bypass the ground pin on the amp's plug to silence noise.

The Noise Doesn't Change

The bridge ground wire may be disconnected, but that's not proof. Magnetic hum isn't supposed to change just because you touch the strings.

If you have a multimeter, you can check the connection on a passive guitar, meaning one whose electronics don't need a battery. Plug a good cable into the guitar only and leave the other end unplugged from the amp. Set the multimeter to resistance and measure between the bridge and the long metal part (the sleeve) of the free plug, not its tip. A reading close to 0 ohms shows that the bridge is connected to the guitar's ground.

Crackles and Dropouts

  • Crackling when you turn a knob or move the selector: The component behind the knob or the selector's contacts may be dirty or worn. If the problem is dirt, a dedicated electrical contact cleaner usually helps. Another possibility is a bad solder joint.

  • Crackling or a dropout when you gently move the cable plug: The problem may be in the cable or in the guitar's jack. Replace the cable first. If the noise comes back with a good cable, have the jack checked.

Noise With Lots of Gain or Compression

High gain, meaning strong amplification of the signal at the input, and compression, which narrows the gap between quiet and loud notes, can bring out hum you can barely hear on a clean sound. If you play with a lot of gain, a noise gate pedal can help. It turns the signal down when it falls below a level you set, so it's mainly useful in the breaks between musical phrases.

In Short

A little hum when a single coil is working on its own is normal. At home, start with a good cable plugged straight into the amp, check the room, and compare selector positions and playing with and without touching the strings. If you felt a tingle or a shock, stop using the equipment and have it checked. It's also worth seeing a technician if crackles continue after cleaning, or if the noise stays with a different cable and a different amp.

 
 
 

Comments


bottom of page