
Tips for Getting the Most Out of Your Pickups
A pickup turns string motion into an electrical signal, but it doesn't work alone. It can only "hear" what the string gives it, from the distance it's set at. That's why even a great pickup can sound weak or dull if the guitar around it isn't set up properly. This article covers what actually affects how your pickups sound, and ends with a practical guide to adjusting pickup height and balance by ear as you play.
Strings
A magnetic pickup responds to string movement because the steel in the string is attracted to the magnet. A few things worth knowing:
Gauge: At the same pitch and the same distance from the pickup, a thicker string tends to produce a stronger signal. On wound strings, the thickness of the steel core and the wrap material matter too, not just the outside diameter. There's no single right choice. It comes down to how you want the strings to feel and sound.
After a significant gauge change: The tension on the neck changes. Check neck relief, action and intonation first, and only then check pickup height.
Material: These names usually describe the wrap around a steel core. Nickel-plated steel is the balanced standard. Pure nickel sounds warmer and rounder and tends to produce a slightly weaker signal. Stainless steel sounds brighter and sharper.
Freshness: Old strings mainly lose high end and sustain, and sometimes tuning accuracy too. A "dull pickup" often turns out to be strings that are a few months old.
Bridge, Saddles, Nut and Tuners
Bridge and Saddles
The bridge is where the strings make contact with the body. Changing saddles (bent steel or solid block, steel or brass) can change the attack and decay of a note, but it's hard to predict by how much, and there's no universal rule. What matters in practice is that the saddles are stable, don't buzz, and form an arc that matches the radius of the fretboard. Raising a saddle moves the string away from the pickup and tends to reduce its output. Lowering it does the opposite. So set your saddle heights for action and playing comfort.
Nut
If the nut slots are too narrow or rough, a string can bind and go out of tune after bends. If a slot is cut too deep, the string will buzz when you play it open, without fretting any note. For a quick check, play the string open, then fret it at the first fret and play it again. If it only buzzes when open, have the nut checked. That's a reason to inspect it, not a reason to file the slot yourself. The nut material (bone, plastic, synthetic materials) mainly affects the sound of open strings, since that's the only time the string rests directly on the nut.
Tuners
In many cases, the small screw at the end of the tuner button works loose. When that happens, the tuner turns too easily and doesn't hold the string tension, and the guitar goes out of tune. Gently tightening the screw with a small Phillips screwdriver fixes it. Don't overtighten: the tuner should still turn smoothly.
Setup and Intonation
A setup covers neck relief, action (string height) and intonation, meaning the guitar plays in tune higher up the neck, not just on the open strings. A few points relate directly to the pickups:
Changing the action changes the distance to the pickups. Every time you raise or lower the bridge, check pickup height again.
Poor intonation is more audible with distortion. Chords that sound sour higher up the neck are usually an intonation problem, not a pickup problem. Check with a tuner, on a clean sound.
Fret buzz can come through the amp as noise or a breaking-up sound. If you can't hear the buzz through the amp and it doesn't cut the note short, there's usually no need to raise the action because of it.
Adjusting Pickup Height
Many players skip this step, even though it has a big effect on the sound. Pickup height changes output, the amount of high end, dynamics and sustain.
Too Close or Too Far
Too close: A stronger signal, which can push your amp or pedals into compression and feel less dynamic. With strong magnets, especially on a Strat, the magnet pulls on the string. The note may sustain for less time, warble, or sound doubled or out of tune (wolf tones). This is most noticeable on the low E string at the upper frets, over the neck pickup. The effect is known as "Stratitis."
Too far: A weaker signal, and a pickup that sounds weak compared to the others.
Starting Point
Measure with the string fretted at the last fret, from the underside of the string to the top of the pole piece or screw below it. These are common starting points, not rules. If the manufacturer publishes a recommendation for your model, start there. The numbers here are for guitar, not bass.
Strat/Tele-style single coil: About 5/64" (2 mm) on the treble side and about 3/32" (2.5 mm) on the bass side for the bridge pickup. The neck pickup a little farther away (about 3/32" (2.5 mm) and 1/8" (3 mm)).
Humbucker: About 1/16" (1.6 mm) on the treble side and about 3/32" (2.4 mm) on the bass side.
P90: A conservative starting point around 3/32" to 1/8" (2.5 to 3 mm), then bring it closer by ear. A dog-ear P90 has no screws for adjusting the height of the whole pickup. To raise it, add a thin shim underneath.
The neck pickup is usually set farther from the strings than the bridge pickup, because the string moves in a wider arc there and gives more signal.
Step by Step, by Ear
Prepare the basics: Fresh strings, a tuned guitar and a finished setup. A clean amp at moderate volume with a neutral tone. Write down the current gap on both sides of each pickup, so you can go back to it.
Start with the bridge pickup: Set it to the starting point and play chords and single notes. If it lacks output, bring it a little closer. If the signal pushes the amp into compression or notes start to warble, move it away. Change a quarter to half a turn at a time, one side at a time, and compare.
Balance the strings: Play each string on its own with the same picking strength and listen. If the wound strings overpower the plain strings, raise the treble side, or the other way around. Set the height of the whole pickup first, and only then fine-tune the balance. On humbuckers and P90s with pole screws, you can also adjust individual strings. On a Strat-style single coil the magnets are fixed: don't push them to balance the strings, as you can damage the coil.
Match the neck pickup to the bridge: Switch between positions and set the neck pickup so switching doesn't cause a big jump in volume. On the neck pickup, pay particular attention to the low E string at the 12th fret and above: if notes warble or sound unstable, move it away.
The middle pickup (on a Strat): Set it to balance with the other two. Many players prefer it a little lower, so it doesn't get in the way of picking or pull on the strings.
Check the combined positions: Positions 2 and 4 on a Strat, and the middle position on two-pickup guitars. A small height change on one of the pickups changes the character of the combination.
Check that the string doesn't touch the pickup: When you pick hard and bend at the upper frets, the string shouldn't hit the pickup or the pole screws.
Check with distortion too: A pickup that sounds balanced clean can be too dominant with distortion, and vice versa.
Play for a few days and check again: Your ears adjust quickly. It's worth coming back to the settings after playing in real situations, at a rehearsal or a recording session.
In Short
A good pickup gives its best when the chain around it is in order: fresh strings that suit your style, a proper setup, a bridge and nut that work as they should, and pickup heights set by ear, not just with a ruler. Most of these improvements cost nothing, just time and patience.
Before buying a new pickup, write down the current heights, try small changes, and compare on a clean sound and on the sound you usually play.
When you order an installation from us, we also set the pickup heights and balance the pickups, and you can try the guitar on the spot. If you're considering a new set, you can browse our Strat-style pickups, Telecaster-style pickups or humbuckers, and ask us anything using the WhatsApp button on the site.


Comments